In [PLC] page, we can measure 2 points length.
1. Left Button Down at 1st point
2. Drag mouse to 2nd point
3. Left Button Up. AOIPuncher shows the length of 2 points in a memo.
切割機的沖孔是選配的, 沖孔的數量可能多達三組, 三組沖頭分別以SP5, SP6, SP7 來表示
因此有勾選項目來設定其是否存在
同時還需要輸入衝子的直徑來做配對
當圓形的直徑符合衝子的直徑, 切割機會以對應的衝子做沖孔加工
CutbotLeather是鞋業方面的排版軟體, 排版軟體所讀入的CAD檔案必須要合乎幾何定義
必須要有一條封閉的輪廓線
筆線要設定為圖層1, 紅色線
刀線要設定為圖層4, 水藍色
檔名須為 裁片名稱-尺寸.dxf 例如 VAMP-40.dxf
A piece dxf should include a close line as a piece outline.
If there are pen lines. the pen lines must be Layer 1 and color should be red.
If there are cut lines. the cut lines must be Layer 4 and color be Aqua.
DXF file name should be PieceName-Size.dxf, such as VAMP-40.dxf
Cutting priority will be modify by ROY accoding to Y position of each punch line.
貼合功能在真皮裁切時用於將電腦檔案與實際放置在切割檯面上的皮革做位置重合的調整
做整體皮料的移動和旋轉的動作
在設定旋轉角度的時候, 可以按 上下左右 移動
AOIPuncher can mix different die in nesting
There are some character
1. Nesting angle is 0 and 180 degree only
2. No Oblique alignment.
3. Punch from large size to small size. It is suitable for punching same part different size.
4. Punch by fix quantity.
5. It mixes different dies (sizes) in a same row.
AOIPuncher 更新的排列方式，可做刀模混和排列在同一捲布料
排列規則
1.只做0度和180度排列
2. 只有方正排列, 不做斜排
3. 大刀先裁, 比較適用於相同部位不同尺碼的部件
4. 只做定量裁切, 不做整排的裁切
5. 可以有多把刀排列在相同的橫排
AOIPuncher new function: Record command into text file
Qty (Q) means Product Pieces (Manufacturing Pieces, Cutting Piece)
Qty/Pair (N) means Pieces in a pair.
When we input Product Pairs (X) then Q = N*X
Make a little adjustment for getting extra pieces.
Move mouse to X and R piece, and clike [left] to adjust X space/pitch,and check if there any overlap.
There are some different options for align position in nesting.
Here I will make some example for different options.
Select Single Piece by click Piece column
Select Muti-Pieces by hold [Shift] and Click Piece column for From-To Select.
Select/unselect Piece by hold [Ctrl] and Click Piece Column.
Then Modify Pieces [Space] and [Mat. Width] and Click [Enter] to modify selected pieces.
There is a function for sorting
Sorting by Size, Area, Name from small to big or from big to small
在CutbotLeather 轉出的CSV裁切檔案會將共用號的鞋片設定為相同的刀塔編號, 亦即為使用相同的刀模
而裁切時AOIPuncher軟體會自動累加相同刀模的裁片數量, 以減少浪費, 增加執行效能
One projector for one form.
If there are more then one form, you should Delete extra form.
Double Click Middle Mouse Button to set form to enable operate, such as Close the form.
If set projector, you should close AOIPuncher and open AOIPuncher again.
CutbotLeather 針對皮料自動排版所用的參數, 我們做盲測來比較不同的參數設定所具備的效益, 包括使用率與所用時間
軟體上的語言包可讓使用者和代理商根據當地的需求自由更改
修改的方法影片有介紹
軟體上的圖標可讓使用者和代理商根據當地的需求自行繪製更改
修改的方法影片有介紹
皮料自動排版, 以整雙的鞋片排列為排列的依據